S12: Beam Column Connection Design

Ver. 3.1.00 2018/09/28 Version 3.1 released.

Ver. 3.0.06 2016/12/06 Fixed resistance factor used in Tensile strength calculation for SANS 10162 - 2005.

Ver. 3.0.05 2016/06/03 Fixed selection problem on Settings dialog.

Ver. 3.0.04 2016/05/17 Fix problem with Check 1 on BS5950 - 2000.

Ver. 3.0.03 2016/04/06 Compatibility problem with large fonts, fixed.

Ver. 3.0.02 2016/01/06 Occasional range check error during start up, fixed.

Ver. 3.0.01 2015/12/09 Correction of licensing error introduced by maintenance release.

Ver. 3.0.00 2015/12/01 Major release. Implemented new user interface library.

Ver. 2.6.04 2015/07/10 Fixed unit conversion error with Eurocode 3 - 2005.

Ver. 2.6.03 2014/11/27 Fixed loads not always reading correctly from saved file.

Ver. 2.6.02 2014/11/21 Added support for Eurocode 3 - 2005.

Ver. 2.6.01 2013/01/16 Recompiled to allow binary compression.

Ver. 2.6.00 2012/12/05 Maintenance release.

Ver. 2.5.03 2010/10/21 Eurocode prying altered, custom section support improved.

Ver. 2.5.02 2010/08/20 Changed Temporary folder location.

Ver. 2.5.01 2010/08/05 Corrected Eurocode specification on startup.

Ver. 2.5.00 2010/07/05 New Release.

Ver. 2.4.05 2009/08/05 Output updated for buckling calcs in BS2000.

Ver. 2.4.04 2009/06/15 Output updated to conform to calcs for BS2000.

Ver. 2.4.03 2009/01/27 Recompiled for compatibility with quest user configurations.

Ver. 2.4.02 2009/01/07 Material factor corrected for SANS 10162:2005 Check 1 Output.

Ver. 2.4.01 2008/09/18 Recompiled for compatibility with Linux servers.

Ver. 2.4.00 2008/03/25 Maintenance release.

Ver. 2.3.02 2007/08/24 Shear test for combined shear of grade 8.8 in Eurocode bolt rectified.

Ver. 2.3.01 2007/07/16 Optimisation of End Plate width fixed.

Ver. 2.3.00 2007/03/09 Maintenance release.

Ver. 2.2.04 2007/02/28 Bolt shear fixed for AISC:LRFD in metric.

Ver. 2.2.03 2006/11/29 Bolt shear fixed for AISC:LRFD.

Ver. 2.2.02 2006/09/20 Loads now recalculated after deleting lines in loads grid with Ctrl-Y.

Ver. 2.2.01 2006/04/20 Design links problem sorted out.

Ver. 2.2.00 2005/12/15 Maintenance release.

Ver. 2.1.02 2005/09/23 Drawing problem: Backing plates from a previous run are now cleared.

Ver. 2.1.01 2004/09/28 Non drawing of erroneous input resolved on Drawing page.

Ver. 2.1.00 2004/09/14 Maintenance release.

Ver. 2.0.01 2003/09/30 Dimension discrepancy in drawing resolved.

Ver. 2.0.00 2003/08/05 Maintenance release.